Skip to content
Fenavia

Guide

FAA Form 8130-3 vs EASA Form 1

FAA Form 8130-3 and EASA Form 1 are the authorized release certificates of the US and EU systems. On both, blocks 13a to 13e release a new part as conforming to approved design, and blocks 14a to 14e release a part back to service after maintenance. A dual release is one maintenance certificate that both authorities accept.

What is FAA Form 8130-3?

FAA Form 8130-3, the Authorized Release Certificate (Airworthiness Approval Tag), is used two ways, and since late 2025 each has its own FAA document:

  • New and newly produced parts. FAA Order 8130.21J (September 2025) covers completing the form for articles produced under 14 CFR part 21. The release is made in blocks 13a to 13e, and the maintenance blocks are shaded out. It is signed by an FAA inspector or designee, an ODA unit member, or a person the production approval holder authorizes (Order 8130.21J, paragraph 7).
  • Return to service after maintenance. AC 43-9D covers this use. The release is made in blocks 14a to 14e, and only people authorized by 14 CFR 43.7 may sign it: certificated mechanics and repair stations among them (AC 43-9D, 23.4.1).

Order 8130.21J cancelled the older Order 8130.21H in 2025, so paperwork guides that still quote 8130.21H are out of date.

What is EASA Form 1?

EASA Form 1 is the EU Authorized Release Certificate. It is set out in two regulations, which EASA publishes as Easy Access Rules for Initial Airworthiness and for Continuing Airworthiness:

  • Production release. A production organization approval holder issues Form 1 for new items under point 21.A.163(c), after checking that they conform to approved design data and are in a condition for safe operation (21.A.165(c)(2)). The completion instructions are in Appendix I to Part 21. Their first paragraph says the certificate's main purpose is to declare the airworthiness of new products and parts.
  • Maintenance release. Under 145.A.50(d), the Form 1 constitutes the component certificate of release to service. Instructions are in Appendix II to Part-M.

How do 8130-3 and Form 1 differ?

The two forms have matching block layouts, so most of the difference is in who issues them and under which rules.

Sources: FAA Order 8130.21J, AC 43-9D, EASA Part 21 and Part-M appendices.
FAA Form 8130-3EASA Form 1
New part releaseBlocks 13a to 13e, under 14 CFR part 21 (Order 8130.21J)Blocks 13a to 13e, under Part 21 (21.A.163, Appendix I)
Who signs a new part releaseFAA inspector or designee, ODA unit member, or a person the production approval holder authorizesA production organization approval holder
Maintenance releaseBlocks 14a to 14e (AC 43-9D)Blocks 14a to 14e (145.A.50, Part-M Appendix II)
Who signs a maintenance releasePersons authorized by 14 CFR 43.7, such as mechanics and repair stationsA Part-145 organization; some Part-M and Part-CAO organizations with a different statement
Shipping document?No (Order 8130.21J; AC 43-9D)No (“not a delivery or shipping note”)
Approval to install?NoNo

What is a dual release?

A dual release is a single maintenance release that both the FAA and EASA accept. It comes from the US-EU Maintenance Annex Guidance (MAG, Change 10, October 2025) under the bilateral aviation safety agreement.

  • A US repair station that also holds EASA approval issues an FAA Form 8130-3 at the end of maintenance and adds the EASA Part-145 statement and approval number in block 12 (MAG Section B, Appendix 1, 10.1 and 10.6).
  • For component maintenance done in the US, the MAG notes that EASA recognizes only the dual-release 8130-3.
  • It works the other way too. An EU organization holding both approvals can issue an EASA Form 1 as a dual release, with block 12 referring to 14 CFR part 43 (MAG Section C, Appendix 1, 7.2.2).
  • Only facilities holding both approvals can issue one; others must issue two separate certificates (AC 43-9D, 23.6.2). EASA's bilateral FAQ adds that a dual release is not acceptable for a “rebuilt” engine or component.

The FAA's own guidance is not consistent on which block 14a boxes to tick for a dual release, so we do not give one rule here. Follow the MAG and the repair station's procedures.

Which certificate should a new part come with?

A new part is released by the production approval holder that made it, under its own authority's rules:

  • The FAA-EASA Technical Implementation Procedures (Revision 7) say each new part exported between the two systems carries the exporting authority's release certificate: an 8130-3 from the US, a Form 1 from the EU (TIP 7.2.2, 7.2.3 and 7.10.1).
  • The MAG says new components released by an EU production approval holder are documented on an EASA Form 1 (Section B, Appendix 1, 10.11.1.2).
  • Standard parts travel with the manufacturer's certificate of conformity instead (TIP 7.10.3).

What are the common paperwork mistakes?

  1. An 8130-3 releasing a new part made under an EASA production approval, for example new Airbus production stock from an EU supplier. Order 8130.21J (11.m) says articles not produced under an FAA production approval are not eligible for an 8130-3, outside a narrow conformity-inspection case, and 14 CFR 21.331 limits FAA export approval to articles made under part 21. Ask how the release was issued. This is about a release as new; a used part can carry an 8130-3 maintenance release from a US repair station.
  2. A used component with an FAA-only 8130-3 going into the EU system. The MAG says used components from a part 145 repair station without EASA approval must not be used, even with an 8130-3 (Section B, 10.11.2.2).
  3. Reading the certificate as approval to install. Neither form approves installing a part on a particular aircraft (Order 8130.21J, 11.m; AC 43-9D, 23.2.1; Part 21 Appendix I, 1.6).
  4. Treating it as the shipping paperwork. Both forms say they are not a delivery or shipping document. Ship a packing slip with it.
  5. Mixing new and maintained items on one certificate. Both systems forbid putting production-released and maintenance-released items on the same form.
  6. Extra remarks in block 12 of a production 8130-3. The Order tells signers not to add statements such as “Domestic shipment only” (11.l).
  7. Unmarked copies and quiet corrections. Copies must be marked COPY or DUPLICATE, and a correction needs a new tracking number and a new signature (Order 8130.21J, 8.e and 8.f; Part 21 Appendix I, 4.2).
  8. Waiting for a Form 1 on standard parts. EASA's acceptable means of compliance to 145.A.42 says one is not normally issued and none should be expected.

Where does Fenavia fit?

Fenavia does not issue release certificates; only the organizations above can. It keeps each stock item's condition and trace details with the part, and carries them onto the ATA 106 form it generates from the sales order, so the paperwork that ships matches what you quoted.

Questions

Is an 8130-3 required for a maintenance release in the US?

Not for a domestic release. FAA AC 43-9D calls Form 8130-3 recommended and its use for return to service optional; what the maintenance record must contain is set by 14 CFR 43.9(a) and 91.417(a).

Can a US repair station release a part for the EU system?

Yes, if it holds both FAA and EASA approval. Under the US-EU Maintenance Annex Guidance it issues an FAA Form 8130-3 with the EASA Part-145 statement in block 12, called a dual release.

Is a release certificate approval to install the part?

No. Both FAA Order 8130.21J and EASA’s Form 1 instructions say the certificate does not by itself approve installing the part on a particular aircraft. The installer still checks eligibility.

Should a standard part come with an EASA Form 1?

Usually not. EASA’s guidance to Part-145 organizations says a Form 1 is not normally issued for standard parts, which come with the manufacturer’s certificate of conformity.

Sources

  1. FAA Order 8130.21J, Completion of FAA Form 8130-3 under Part 21 (09/25/2025)
  2. FAA AC 43-9D, Maintenance Records and FAA Form 8130-3 Return to Service (09/22/2025)
  3. 14 CFR 21.331, Issue of export airworthiness approvals
  4. 14 CFR 43.7, Persons authorized to approve for return to service
  5. EASA Easy Access Rules for Initial Airworthiness (Part 21, incl. Appendix I)
  6. EASA Easy Access Rules for Continuing Airworthiness (Part-145, Part-M Appendix II)
  7. US-EU Maintenance Annex Guidance (MAG), Change 10
  8. FAA-EASA Technical Implementation Procedures, Revision 7 with Amendment 1
  9. EASA FAQ: bilateral agreement (BASA) and continuing airworthiness
What is ATA Spec 106?What ATA Spec 106 is, what its traceability form records, when parts traders use it, and why it is not an airworthiness release like an 8130-3 or Form 1.Back-to-birth traceability for aircraft partsWhat back-to-birth traceability means for aircraft parts, which rules require life-limited part records, and what a trader should collect before buying.Aircraft part condition codes: NE, NS, OH, SV, AR and the restWhat the aircraft part condition codes NE, NS, OH, RP, SV, AR and the rest mean, which ones a rule defines, and how traders compare quotes across them.

Paperwork that matches the quote.

See how Fenavia carries condition and trace details from stock to the ATA 106 form, with your own parts.

Book a demo